View L78L12ABD-TR_8907342.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

this is information on a product in full production. april 2014 docid2145 rev 22 1/47 l78l positive voltage regulators datasheet - production data features ? output current up to 100 ma ? output voltages of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 v thermal overload protection ? short-circuit protection ? no external components are required ? available in either 4% (a) or 8% (c) selection description the l78l series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. if adequate heat-sink is provided, they can deliver up to 100 ma output current. they are intended as fixed voltage regulators in a wide range of applications including local or on- card regulation for elimination of noise and distribution problems associated with single-point regulation. in addition, they can be used with power pass elements to make high-current voltage regulators. the l78l series used as zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. 627 72 62 w
contents l78l 2/47 docid2145 rev 22 contents 1 diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 typical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6 typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.1 to-92 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.2 so-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 7.3 sot-89 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8 packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.1 tape and reel for to-92 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.2 tape and reel for so-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.3 tape and reel for sot-89 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 9 order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 10 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
docid2145 rev 22 3/47 l78l diagram 47 1 diagram figure 1. schematic diagram
pin configuration l78l 4/47 docid2145 rev 22 2 pin configuration figure 2. pin connection (top view, bottom view for to-92) sot-89 so-8 to-92 pin 1 = v out pin 2 = gnd pin 3 = v in figure 3. test circuits
docid2145 rev 22 5/47 l78l maximum ratings 47 3 maximum ratings table 1. absolute maximum ratings symbol parameter value unit v i dc input voltage v o = 3.3 to 9 v 30 v v o = 12 to 15 v 35 v o = 18 to 24 v 40 i o output current 100 ma p d power dissipation internally limited (1) 1. our so-8 package used for voltage regulators is modified interna lly to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. this particular fram e decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. the external dimensions are the same as for the standard so-8. mw t stg storage temperature range -65 to 150 c t op operating junction temperature range for l78lxxac / l78lxxc 0 to 125 c for l78lxxab -40 to 125 table 2. thermal data symbol parameter so-8 to-92 sot-89 unit r thjc thermal resistance junction-case (max) 20 15 c/w r thja thermal resistance junction-ambient (max) 55 (1) 200 55 (1) c/w 1. considering 6 cm2 of copper board heat-sink.
electrical characteristics l78l 6/47 docid2145 rev 22 4 electrical characteristics refer to the test circuits, t j = 0 to 125 c, v i = 8.3 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 3. electrical characteristics of l78l33c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 3.036 3.3 3.564 v v o output voltage i o = 1 to 40 ma, v i = 5.3 to 20 v 2.97 3.63 v i o = 1 to 70 ma, v i = 8.3 v 2.97 3.63 dv o line regulation v i = 5.3 to 20 v, t j = 25 c 150 mv v i = 6.3 to 20 v, t j = 25 c 100 dv o load regulation i o = 1 to 100 ma, t j = 25 c 60 mv i o = 1 to 40 ma, t j = 25 c 30 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 6.3 to 20 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 40 v svr supply voltage rejection v i = 6.3 to 16.3 v, f = 120 hz i o = 40 ma, t j = 25 c 41 49 db v d dropout voltage 1.7 v
docid2145 rev 22 7/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c, v i = 10 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 4. electrical characteristics of l78l05c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 4.6 5 5.4 v v o output voltage i o = 1 to 40 ma, v i = 7 to 20 v 4.5 5.5 v i o = 1 to 70 ma, v i = 10 v 4.5 5.5 dv o line regulation v i = 8.5 to 20 v, t j = 25 c 200 mv v i = 9 to 20 v, t j = 25 c 150 dv o load regulation i o = 1 to 100 ma, t j = 25 c 60 mv i o = 1 to 40 ma, t j = 25 c 30 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 8 to 20 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 40 v svr supply voltage rejection v i = 9 to 20 v, f = 120 hz i o = 40 ma, t j = 25 c 40 49 db v d dropout voltage 1.7 v
electrical characteristics l78l 8/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c,v i = 14 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 5. electrical characteristics of l78l08c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 7.36 8 8.64 v v o output voltage i o = 1 to 40 ma, v i = 8.5 to 20 v 7.2 8.8 v i o = 1 to 70 ma, v i = 12 v 7.2 8.8 dv o line regulation v i = 8.5 to 20 v, t j = 25 c 200 mv v i = 9 to 20 v, t j = 25 c 150 dv o load regulation i o = 1 to 100 ma, t j = 25 c 80 mv i o = 1 to 40 ma, t j = 25 c 40 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 8 to 20 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 60 v svr supply voltage rejection v i = 9 to 20 v, f = 120 hz i o = 40 ma, t j = 25 c 36 45 db v d dropout voltage 1.7 v
docid2145 rev 22 9/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c, v i = 15 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 6. electrical characteristics of l78l09c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 8.28 9 9.72 v v o output voltage i o = 1 to 40 ma, v i = 11.5 to 23 v 8.1 9.9 v i o = 1 to 70 ma, v i = 15 v 8.1 9.9 dv o line regulation v i = 11.5 to 23 v, t j = 25 c 250 mv v i = 12 to 23 v, t j = 25 c 200 dv o load regulation i o = 1 to 100 ma, t j = 25 c 80 mv i o = 1 to 40 ma, t j = 25 c 40 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 12 to 23 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 70 v svr supply voltage rejection v i = 12 to 23 v, f = 120 hz i o = 40 ma, t j = 25 c 36 44 db v d dropout voltage 1.7 v
electrical characteristics l78l 10/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c, v i = 16 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 7. electrical characteristics of l78l10c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 9.2 10 10.8 v v o output voltage i o = 1 to 40 ma, v i = 12.5 to 23 v 9 11 v i o = 1 to 70 ma, v i = 16 v 9 11 dv o line regulation v i = 12.5 to 23 v, t j = 25 c 230 mv v i = 13 to 23 v, t j = 25 c 170 dv o load regulation i o = 1 to 100 ma, t j = 25 c 80 mv i o = 1 to 40 ma, t j = 25 c 40 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 13 to 23 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 60 v svr supply voltage rejection v i = 14 to 23 v, f = 120 hz i o = 40 ma, t j = 25 c 37 45 db v d dropout voltage 1.7 v
docid2145 rev 22 11/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c, v i = 19 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 8. electrical characteristics of l78l12c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 11.1 12 12.9 v v o output voltage i o = 1 to 40 ma, v i = 14.5 to 27 v 10.8 13.2 v i o = 1 to 70 ma, v i = 19 v 10.8 13.2 dv o line regulation v i = 14.5 to 27 v, t j = 25 c 250 mv v i = 16 to 27 v, t j = 25 c 200 dv o load regulation i o = 1 to 100 ma, t j = 25 c 100 mv i o = 1 to 40 ma, t j = 25 c 50 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 16 to 27 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 80 v svr supply voltage rejection v i = 15 to 25 v, f = 120 hz i o = 40 ma, t j = 25 c 36 42 db v d dropout voltage 1.7 v
electrical characteristics l78l 12/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c, v i = 23 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified table 9. electrical characteristics of l78l15c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 13.8 15 16.2 v v o output voltage i o = 1 to 40 ma, v i = 17.5 to 30 v 13.5 16.5 v i o = 1 to 70 ma, v i = 23 v 13.5 16.5 dv o line regulation v i = 17.5 to 30 v, t j = 25 c 300 mv v i = 20 to 30 v, t j = 25 c 250 dv o load regulation i o = 1 to 100 ma, t j = 25 c 150 mv i o = 1 to 40 ma, t j = 25 c 75 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 20 to 30 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 90 v svr supply voltage rejection v i = 18.5 to 28.5 v, f = 120 hz i o = 40 ma, t j = 25 c 33 39 db v d dropout voltage 1.7 v
docid2145 rev 22 13/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c, v i = 27 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 10. electrical characteristics of l78l18c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 16.6 18 19.4 v v o output voltage i o = 1 to 40 ma, v i = 22 to 33 v 16.2 19.8 v i o = 1 to 70 ma, v i = 27 v 16.2 19.8 dv o line regulation v i = 22 to 33 v, t j = 25 c 320 mv v i = 22 to 33 v, t j = 25 c 270 dv o load regulation i o = 1 to 100 ma, t j = 25 c 170 mv i o = 1 to 40 ma, t j = 25 c 85 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 23 to 33 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 120 v svr supply voltage rejection v i = 23 to 33 v, f = 120 hz i o = 40 ma, t j = 25 c 32 38 db v d dropout voltage 1.7 v
electrical characteristics l78l 14/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c, v i = 33 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 11. electrical characteristics of l78l24c symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 22.1 24 25.9 v v o output voltage i o = 1 to 40 ma, v i = 27 to 38 v 21.6 26.4 v i o = 1 to 70 ma, v i = 33 v 21.6 26.4 dv o line regulation v i = 27 to 38 v, t j = 25 c 350 mv v i = 28 to 38 v, t j = 25 c 300 dv o load regulation i o = 1 to 100 ma, t j = 25 c 200 mv i o = 1 to 40 ma, t j = 25 c 100 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.2 ma v i = 28 to 38 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 200 v svr supply voltage rejection v i = 29 to 35 v, f = 120 hz i o = 40 ma, t j = 25 c 30 37 db v d dropout voltage 1.7 v
docid2145 rev 22 15/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab),v i = 8.3 v, i o = 40ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 12. electrical characteristics of l78l33ab and l78l33ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 3.168 3.3 3.432 v v o output voltage i o = 1 to 40 ma, v i = 5.3 to 20 v 3.135 3.465 v i o = 1 to 70 ma, v i = 8.3 v 3.135 3.465 dv o line regulation v i = 5.3 to 20 v, t j = 25 c 150 mv v i = 6.3 to 20 v, t j = 25 c 100 dv o load regulation i o = 1 to 100 ma, t j = 25 c 60 mv i o = 1 to 40 ma, t j = 25 c 30 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 6.3 to 20 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 40 v svr supply voltage rejection v i = 6.3 to 16.3 v, f = 120 hz i o = 40 ma, t j = 25 c 41 49 db v d dropout voltage 1.7 v
electrical characteristics l78l 16/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab), v i = 10 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 13. electrical characteristics of l78l05ab and l78l05ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 4.8 5 5.2 v v o output voltage i o = 1 to 40 ma, v i = 7 to 20 v 4.75 5.25 v i o = 1 to 70 ma, v i = 10 v 4.75 5.25 dv o line regulation v i = 7 to 20 v, t j = 25 c 150 mv v i = 8 to 20 v, t j = 25 c 100 dv o load regulation i o = 1 to 100 ma, t j = 25 c 60 mv i o = 1 to 40 ma, t j = 25 c 30 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 8 to 20 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 40 v svr supply voltage rejection v i = 8 to 18 v, f = 120 hz i o = 40 ma, t j = 25 c 41 49 db v d dropout voltage 1.7 v
docid2145 rev 22 17/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab), v i = 12 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 14. electrical characteristics of l78l06ab and l78l06ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 5.76 6 6.24 v v o output voltage i o = 1 to 40 ma, v i = 8.5 to 20 v 5.7 6.3 v i o = 1 to 70 ma, v i = 12 v 5.7 6.3 v o line regulation v i = 8.5 to 20 v, t j = 25 c 150 mv v i = 9 to 20 v, t j = 25 c 100 v o load regulation i o = 1 to 100 ma, t j = 25 c 60 mv i o = 1 to 40 ma, t j = 25 c 30 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma i d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 9 to 20 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 50 v svr supply voltage rejection v i = 9 to 20 v, f = 120 hz i o = 40 ma, t j = 25 c 39 46 db v d dropout voltage 1.7 v
electrical characteristics l78l 18/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab), v i = 14 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 15. electrical characteristics of l78l08ab and l78l08ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 7.68 8 8.32 v v o output voltage i o = 1 to 40 ma, v i = 10.5 to 23 v 7.6 8.4 v i o = 1 to 70 ma, v i = 14 v 7.6 8.4 dv o line regulation v i = 10.5 to 23 v, t j = 25 c 175 mv v i = 11 to 23 v, t j = 25 c 125 dv o load regulation i o = 1 to 100 ma, t j = 25 c 80 mv i o = 1 to 40 ma, t j = 25 c 40 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 11 to 23 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 60 v svr supply voltage rejection v i = 12 to 23 v, f = 120 hz i o = 40 ma, t j = 25 c 37 45 db v d dropout voltage 1.7 v
docid2145 rev 22 19/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab), v i =15 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 16. electrical characteristics of l78l09ab and l78l09ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 8.64 9 9.36 v v o output voltage i o = 1 to 40 ma, v i = 11.5 to 23 v 8.55 9.45 v i o = 1 to 70 ma, v i = 15 v 8.55 9.45 dv o line regulation v i = 11.5 to 23 v, t j = 25 c 225 mv v i = 12 to 23 v, t j = 25 c 150 dv o load regulation i o = 1 to 100 ma, t j = 25 c 80 mv i o = 1 to 40 ma, t j = 25 c 40 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 12 to 23 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 70 v svr supply voltage rejection v i = 12 to 23 v, f = 120 hz i o = 40 ma, t j = 25 c 37 44 db v d dropout voltage 1.7 v
electrical characteristics l78l 20/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab), v i = 16 v, i o = 40ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 17. electrical characteristics of l78l10ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 9.6 10 10.4 v v o output voltage i o = 1 to 40 ma, v i = 12.5 to 23 v 9.5 10.5 v i o = 1 to 70 ma, v i = 16 v 9.5 10.5 dv o line regulation v i = 12.5 to 23 v, t j = 25 c 230 mv v i = 13 to 23 v, t j = 25 c 170 dv o load regulation i o = 1 to 100 ma, t j = 25 c 80 mv i o = 1 to 40 ma, t j = 25 c 40 i d quiescent current t j = 25 c 6 ma t j = 125 c 5.5 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 13 to 23 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 60 v svr supply voltage rejection v i = 14 to 23 v, f = 120 hz i o = 40 ma, t j = 25 c 37 45 db v d dropout voltage 1.7 v
docid2145 rev 22 21/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab), v i =19 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 18. electrical characteristics of l78l12ab and l78l12ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 11.5 12 12.5 v v o output voltage i o = 1 to 40 ma, v i = 14.5 to 27 v 11.4 12.6 v i o = 1 to 70 ma, v i = 19 v 11.4 12.6 dv o line regulation v i = 14.5 to 27 v, t j = 25 c 250 mv v i = 16 to 27 v, t j = 25 c 200 dv o load regulation i o = 1 to 100 ma, t j = 25 c 100 mv i o = 1 to 40 ma, t j = 25 c 50 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 16 to 27 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 80 v svr supply voltage rejection v i = 15 to 25 v, f = 120 hz i o = 40 ma, t j = 25 c 37 42 db v d dropout voltage 1.7 v
electrical characteristics l78l 22/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab),v i = 23 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 19. electrical characteristics of l78l15ab and l78l15ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 14.4 15 15.6 v v o output voltage i o = 1 to 40 ma, v i = 17.5 to 30 v 14.25 15.75 v i o = 1 to 70 ma, v i = 23 v 14.25 15.75 dv o line regulation v i = 17.5 to 30 v, t j = 25 c 300 mv v i = 20 to 30 v, t j = 25 c 250 dv o load regulation i o = 1 to 100 ma, t j = 25 c 150 mv i o = 1 to 40 ma, t j = 25 c 75 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 20 to 30 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 90 v svr supply voltage rejection v i = 18.5 to 28.5 v, f = 120 hz i o = 40 ma, t j = 25 c 34 39 db v d dropout voltage 1.7 v
docid2145 rev 22 23/47 l78l electrical characteristics 47 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab),v i = 27 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 20. electrical characteristics of l78l18ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 17.3 18 18.7 v v o output voltage i o = 1 to 40 ma, v i = 22 to 33 v 17.1 18.9 v i o = 1 to 70 ma, v i = 27 v 17.1 18.9 dv o line regulation v i = 22 to 33 v, t j = 25 c 320 mv v i = 22 to 33 v, t j = 25 c 270 dv o load regulation i o = 1 to 100 ma, t j = 25 c 170 mv i o = 1 to 40 ma, t j = 25 c 85 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 23 to 33 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 120 v svr supply voltage rejection v i = 23 to 33 v, f = 120 hz i o = 40 ma, t j = 25 c 33 38 db v d dropout voltage 1.7 v
electrical characteristics l78l 24/47 docid2145 rev 22 refer to the test circuits, t j = 0 to 125 c (ac) t j = -40 to 125 c (ab),v i = 33 v, i o = 40 ma, c i = 0.33 f, c o = 0.1 f unless otherwise specified. table 21. electrical characteristics of l78l24ab and l78l24ac symbol parameter test conditions min. typ. max. unit v o output voltage t j = 25 c 23 24 25 v v o output voltage i o = 1 to 40 ma, v i = 27 to 38 v 22.8 25.2 v i o = 1 to 70 ma, v i = 33 v 22.8 25.2 dv o line regulation v i = 27 to 38 v, t j = 25 c 350 mv v i = 28 to 38 v, t j = 25 c 300 dv o load regulation i o = 1 to 100 ma, t j = 25 c 200 mv i o = 1 to 40 ma, t j = 25 c 100 i d quiescent current t j = 25 c 6.5 ma t j = 125 c 6 ma di d quiescent current change i o = 1 to 40 ma 0.1 ma v i = 28 to 38 v 1.5 en output noise voltage b = 10 hz to 100 khz, t j = 25 c 200 v5y svr supply voltage rejection v i = 29 to 33 v, f = 120 hz i o = 40 ma, t j = 25 c 31 37 db v d dropout voltage 1.7 v
docid2145 rev 22 25/47 l78l typical performance 47 5 typical performance figure 4. l78l05/12 output voltage vs. ambient temperature figure 5. l78l05/12/24 load characteristics figure 6. l78l05/12/24 thermal shutdown figure 7. l78l05/12 quiescent current vs. output current
typical performance l78l 26/47 docid2145 rev 22 figure 8. l78l05 quiescent current vs. input voltage figure 9. l78l05/12/24 output characteristics figure 10. l78l05/12/24 ripple rejection figure 11. l78l05 dropout characteristics figure 12. l78l short-circuit output current
docid2145 rev 22 27/47 l78l typical application 47 6 typical application figure 13. high output current short-circuit protected figure 14. outuput boost circuit
typical application l78l 28/47 docid2145 rev 22 figure 15. current regulator figure 16. adjustable output regulator
docid2145 rev 22 29/47 l78l package mechanical data 47 7 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. 7.1 to-92 figure 17. to-92 drawing 0102782 d
package mechanical data l78l 30/47 docid2145 rev 22 table 22. to-92 mechanical data dim. mm min. typ. max. a4.32 4.95 b0.36 0.51 d4.45 4.95 e3.30 3.94 e2.41 2.67 e1 1.14 1.40 l 12.70 15.49 r2.16 2.41 s1 0.92 1.52 w0.41 0.56 v5
docid2145 rev 22 31/47 l78l package mechanical data 47 7.2 so-8 figure 18. so-8 drawing 0016023_g_fu
package mechanical data l78l 32/47 docid2145 rev 22 table 23. so-8 mechanical data dim. mm min. typ. max. a 1.75 a1 0.10 0.25 a2 1.25 b0.31 0.51 b1 0.28 0.48 c0.10 0.25 c1 0.10 0.23 d4.804.905.00 e5.806.006.20 e1 3.80 3.90 4.00 e1.27 h0.25 0.50 l0.40 1.27 l1 1.04 l2 0.25 k0 8 ccc 0.10
docid2145 rev 22 33/47 l78l package mechanical data 47 figure 19. so-8 footprint footprint_0016023_g_fu
package mechanical data l78l 34/47 docid2145 rev 22 7.3 sot-89 figure 20. sot-89 drawings b5(9b( b5(9b(
docid2145 rev 22 35/47 l78l package mechanical data 47 table 24. sot-89 mechanical data dim. mm min. typ. max. a 1.40 1.60 b 0.44 0.56 b1 0.36 0.48 c 0.35 0.44 c1 0.35 0.44 d 4.40 4.60 d1 1.62 1.83 d3 0.90 e 2.29 2.60 e 1.42 1.57 e1 2.92 3.07 h 3.94 4.25 h1 2.70 3.10 k1 8 l 0.89 1.20 r0.25 b90
package mechanical data l78l 36/47 docid2145 rev 22 figure 21. sot-89 footprint )rrwsulqw
docid2145 rev 22 37/47 l78l packaging mechanical data 47 8 packaging mechanical data 8.1 tape and reel for to-92 figure 22. to-92 tape and reel dimensions : : : : $ g ' + + + / o ) ) 3 3 ghowd3 ghowd+ 7 7 7 w '5$:,1*127 ,16& $/(
packaging mechanical data l78l 38/47 docid2145 rev 22 table 25. to-92 tape and reel mechanical data dim. mm min. typ. max. a1 4.80 t 3.80 t1 1.60 t2 2.30 d 0.45 0.47 0.48 p0 12.50 12.70 12.90 p2 5.65 6.35 7.05 f1, f2 2.40 2.50 2.94 f3 4.98 5.08 5.48 delta h -2.00 2.00 w 17.50 18.00 19.00 w0 5.56.006.5 w1 8.50 9.00 9.25 w2 0.50 h 18.50 21 h3 0.5 1 2 h0 15.50 16.00 18.8 h1 25.0 27.0 d0 3.80 4.00 4.20 t 0.90 l 11.00 l1 3.00 delta p -1.00 1.00 ?1 352 355 358 ?2 28 30 32 u444750
docid2145 rev 22 39/47 l78l packaging mechanical data 47 figure 23. to-92 ammopack mechanical data drawing w w1 w0 w2 a 1 d d0 h1 h h0 l l1 f1 f2 p2 p0 delta h t2 t1 t t f3 h3 0050910s_rev_u
packaging mechanical data l78l 40/47 docid2145 rev 22 table 26. to-92 ammopack mechanical data dim. mm min. typ. max. a1 4.80 t 3.80 t1 1.60 t2 2.30 d 0.45 0.47 0.48 p0 12.50 12.70 12.90 p2 5.65 6.35 7.05 f1, f2 2.40 2.50 2.94 f3 4.98 5.08 5.48 delta h -2.00 2.00 w 17.50 18.00 19.00 w0 5.56.006.5 w1 8.50 9.00 9.25 w2 0.50 h 18.50 21 h3 0.5 1 2 h0 15.50 16.00 18.8 h1 25.0 27.0 d0 3.80 4.00 4.20 t 0.90 l 11.00 l1 3.00 delta p -1.00 1.00
docid2145 rev 22 41/47 l78l packaging mechanical data 47 8.2 tape and reel for so-8 figure 24. so-8 tape and reel dimensions figure 25. so-8 tape and reel mechanical data dim. mm min. typ. max. a - 330 c 12.8 13.2 d20.2 n60 t 22.4 ao 8.1 8.5 bo 5.5 5.9 ko 2.1 2.3 po 3.9 4.1 p7.9 8.1
packaging mechanical data l78l 42/47 docid2145 rev 22 8.3 tape and reel for sot-89 figure 26. sot-89 carrier tape drawing table 27. sot-89 carrier tape dimensions dim. mm. values tolerance ao 4.52 0.10 bo 4.91 0.10 ko 1.90 0.10 f 5.50 0.10 e 1.75 0.10 w12 0.30 p2 2 0.10 po 4 0.10 p1 8 0.10 t 0.30 0.10 d ? 1.55 0.05 d1 ? 1.60 0.10 b(
docid2145 rev 22 43/47 l78l order codes 47 9 order codes table 28. order codes part numbers output voltages (v) so-8 to-92 (bag) (1) to-92 (ammopack) to-92 (tape and reel) sot-89 l78l33abd-tr l78l33abz-ap l78l33abutr 3.3 l78l33acd13tr l78l33az l78l33acz-ap l78l33acztr l78l33acutr 3.3 l78l33cd-tr 3.3 l78l05abd13tr l78l05abz l78l05abz-ap l78l05abz-tr l78l05abutr 5 l78l05acd13tr l78l05acz l78l05acz-ap l78l05acztr l78l05acutr 5 l78l05cd13tr l78l05cz 5 l78l06abz l78l06abutr 6 l78l06acd13tr l78l06acutr 6 l78l08abd13tr l78l08abz-ap l78l08abztr l78l08abutr 8 l78l08acd13tr l78l08acz l78l08acz-ap l78l08acztr l78l08acutr 8 l78l08cd13tr 8 l78l09abd13tr l78l09abz l78l09abutr 9 l78l09acd13tr l78l09acz-ap l78l09acz-tr l78l09acutr 9 l78l09cd13tr 9 l78l10acutr 10 L78L12ABD-TR l78l12abz l78l12abz-ap l78l12abutr 12 l78l12acd13tr l78l12acz l78l12acz-ap l78l12acz-tr l78l12acutr 12 l78l12cd13tr 12 l78l15abz-ap l78l15abutr 15 l78l15acd13tr l78l15acz l78l15acutr 15 l78l15cd-tr 15 l78l18acutr 18 l78l18cd13tr 18 l78l24abz-tr 24 l78l24acz-ap l78l24acutr 24 l78l24cd-tr 24 1. available in ammopak with the suffix "-ap" or in tape and reel with the suffix "tr". please note that in these cases pins ar e shaped according to tape and reel specifications.
order codes l78l 44/47 docid2145 rev 22 table 29. marking information part numbers marking packages output voltages l78l05abd13tr 78l05b so-8 5 v l78l05abd13tr 8c sot-89 5 v l78l05abz l78l05 to-92 5 v l78l05abz-ap l78l05 to-92 5 v l78l05abz-tr l78l05 to-92 5 v l78l05acd13tr l78l05a so-8 5 v l78l05acd13tr 8c sot-89 5 v l78l05acz l78l05 to-92 5 v l78l05acz-ap l78l05 to-92 5 v l78l05acztr l78l05 to-92 5 v l78l05cd13tr 78l05 so-8 5 v l78l05cd13tr l78l05 to-92 5 v l78l06abutr 8e sot-89 6 v l78l06abz l78l06 to-92 6 v l78l06acd13tr l78l06a so-8 6 v l78l06acd13tr 8e sot-89 6 v l78l08abd13tr 78l08b so-8 8 v l78l08abd13tr 8g sot-89 8 v l78l08abz-ap l78l08 to-92 8 v l78l08abztr l78l08 to-92 8 v l78l08acd13tr 78l08a so-8 8 v l78l08acd13tr 8g sot-89 8 v l78l08acz l78l08 to-92 8 v l78l08acz-ap l78l08 to-92 8 v l78l08acztr l78l08a to-92 8 v l78l08cd13tr 78l08 so-8 8 v l78l09abd13tr 78l09b so-8 8 v l78l09abz l78l09 to-92 9 v l78l09acd13tr 78l09a so8 9 v l78l09acd13tr 8h sot-89 9 v l78l09acz-ap l78l09 to-92 9 v l78l09acz-tr l78l09 to-92 9 v l78l09cd13tr 78l09 so-8 9 v l78l09cd13tr 8i sot-89 10 v L78L12ABD-TR 78l12b so-8 12 v
docid2145 rev 22 45/47 l78l order codes 47 L78L12ABD-TR 8k sot-89 12 v l78l12abz l78l12 to-92 12 v l78l12abz-ap l78l12 to 92 12 v l78l12acd13tr 78l12a so-8 5 v l78l12acd13tr 8k to-92 5 v l78l12acz l78l12 to-92 12 v l78l12acz-ap l78l12 to-92 12 v l78l12acz-tr l78l12 to-92 12 v l78l12cd13tr 78l12 so-8 12 v l78l15abutr 8l sot-89 15 v l78l15abz-ap l78l15 to-92 15 v l78l15acd13tr 78l15a so-8 15 v l78l15acd13tr 8l sot-89 15 v l78l15acz l78l15 to-92 15 v l78l15cd-tr 78l15 so-8 15 v l78l18acutr 8b sot-89 18 v l78l24abz-tr l78l24 to-92 24 v l78l24acutr 8p sot-89 24 v l78l24acz-ap l78l24 to-92 24 v l78l33abd-tr 78l33b so-8 3.3 v l78l33abd-tr 8a sot-89 3.3 v l78l33abz-ap l78l33 to-92 3.3 v l78l33acd13tr 78l33a so-8 3.3 v l78l33acutr 8a sot-89 3.3 v l78l33acz l78l33 to-92 3.3 v l78l33acz-ap l78l33 to-92 3.3 v table 29. marking information (continued) part numbers marking packages output voltages
revision history l78l 46/47 docid2145 rev 22 10 revision history table 30. document revision history date revision changes 14-mar-2005 9 add tape and reel for to-92. 15-mar-2005 10 add note on table 3. 23-dec-2005 11 mistake on ordering table in header. 12-sep-2006 12 order codes updated. 07-jun-2007 13 order codes updated. 18-sep-2007 14 added table 1 in cover page. 15-jul-2008 15 modified: table 1 and table 28: order codes . 18-aug-2008 16 modified figure 12 on page 26 . 03-apr-2009 17 added: r thja value for sot-89 table 2 on page 5 . 08-feb-2011 18 added note table 24 on page 35 21-feb-2012 19 modified: sot-89 figure 2 on page 4 . 14-aug-2012 20 updated t op value for l78l00ac in table 1 on page 5 . minor text changes. 07-sep-2012 21 added: table 29: marking information . 14-apr-2014 22 part numbers l78lxxab, l78lxxac, l78lxxc changed to l78l. removed table1: device summary. updated features and description in cover page, table 28: order codes , table 29: marking information and section 7: package mechanical data . added section 8: packaging mechanical data . minor text changes.
docid2145 rev 22 47/47 l78l 47 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statem ents and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or register ed trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2014 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - swed en - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of L78L12ABD-TR

	To Download L78L12ABD-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .